Rainbow-electronics FARGO MAESTRO 100 (with TCP_IP) Manuel d'utilisateur Page 258
- Page / 787
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Data Commands
DTE-DCE Local Rate Reporting +ILRR
©Restricted
Page: 68 / 156
This document is the sole and exclusive property of Wavecom. Not to be distributed or divulged without
prior written agreement.
WM_DEV_OAT_UGD_049 - 001 VOLUME 2 August 23, 2007
13.3 DTE-DCE Local Rate Reporting +ILRR
13.3.1 Description
This command controls whether a +ILRR unsolicited response is sent to the
application with the current (negotiated or renegotiated) DTE-DCE speed rate.
If enabled, the unsolicited result code is transmitted in an incoming or outgoing data
call, after any data compression report, and before any connection indication
(CONNECT).
13.3.2 Syntax
Action command
AT+ILRR=<value>
OK
Read command
AT+ILRR?
+ILRR: <value>
OK
Test command
AT+ILRR=?
+ILRR: (list of supported <value>s)
OK
Unsolicited response
+ILRR: <rate>
- AT Commands Interface Guide 1
- Firmware v6.63 1
- Trademarks 3
- Copyright 3
- Overview 4
- Document History 5
- VOLUME 1 8
- ©Restricted 10
- 1 Introduction 11
- Introduction 12
- 1.2 Related Documents 12
- 1.3 ETSI Secretariat 14
- 2 AT Commands Features 21
- AT Commands Features 22
- 2.7 Length of Phone Numbers 23
- 2.8 Bad Software Message 23
- 4 Identifications commands 26
- Note: Request IMEI SVN 40
- Note: Update the IMEI SVN 40
- 5 Open AT 42
- Commands 42
- Com mand Responses 43
- Commands 46
- <err>" 55
- Note: Enable slow idle mode 87
- Note: Disable slow idle mode 87
- Note: Idem 97
- Action command 100
- Read command 100
- Test command 100
- Command Responses 101
- Note: Done 101
- Note: Possible values 108
- Note: Custom character set 108
- Note: Get current value 108
- Note: Get possible values 108
- Unsolicited response 112
- 7 Wireless CPU 119
- Status Commands 119
- Wireless CPU 121
- Status Commands 121
- 8 Serial Port Commands 140
- Note: Enables autobauding 143
- Serial Port Commands 145
- Note: New values 146
- Note: Current values 146
- Note: Get supported values 169
- Note: Enter multiplex mode 169
- Note: Get current values 169
- Note: No OK 170
- Security Commands 171
- Related Documents 192
- Contents 194
- VOLUME 2 194
- GSM Network Commands 200
- Unsollicited response 215
- >: Location Area Code 216
- <CI>: 216
- <NetMeas>: 216
- <BCCHlist>: 217
- <TA>: 217
- <Date and Time>: 217
- Note: <rssi> is 23 221
- Call Control Commands 225
- 12.8 Remote disconnection 239
- Note: Current value 245
- Note: CSD data call 251
- Note: Incoming voice call 253
- 13 Data Commands 254
- Data Commands 256
- Note: Select a bearer 257
- Note: CSD call 260
- Note: Data rate is 9600 260
- Note: Set new parameters 262
- Intermediate response 271
- Note: Reporting enabled 272
- Note: outgoing data call 272
- Note: No error correction 274
- Note: Enter GSM mode 276
- GPRS Commands 279
- Note: Delete <cid>=1 286
- CONNECT 295
- Note: Context 2 is active 325
- PLMN Commands 331
- Contents 350
- VOLUME 3 350
- Phonebooks Commands 353
- Note: ADN phonebook 370
- Note: Test command 396
- Note: Possible services 406
- Short message Commands 410
- OK), but the 412
- Write, send: SMS 420
- Test command1 429
- Note: New message received 439
- SIM Commands 473
- (e.g. for 483
- (SMS, phonebook…) 484
- SIM ToolKit Commands 485
- Note: Select Item 1 506
- Note: End of session 506
- 20.2.4 Parameter Storage 514
- 20.3.4 Parameter Storage 517
- 20.5.2 Syntax 521
- 20.5.1 Description 521
- 20.5.4 Parameter Storage 522
- 20.6.4 Parameter Storage 526
- 20.7.4 Parameter Storage 529
- Note: Sequence not allowed 538
- 20.11.1 Description 539
- 20.11.2 Syntax 539
- VOLUME 4 552
- Note: Activate config1 555
- Audio Commands 556
- Note: Stop DTMF decoding 597
- DTMF Decoding 598
- Note: Selects the buzzer 615
- Action Command 620
- Read Command 620
- I/O Commands 623
- Note: GPIO state is written 631
- Battery Commands 642
- °C mV °C mV °C mV 647
- AT+WDIAG=0,1,5,0,0,0,0 652
- +WDIAGI: 3 654
- +WDIAGI: 4,4300 654
- CPHS Commands 658
- Note: Activate line 1 670
- 25 Fax Commands 671
- V.17 type modem 673
- Fax class 2 Commands 696
- Note: Change bit rate 697
- APPENDIXES 707
- © Restricted 709
- 1 Codes and Values 710
- 1.7 Result Codes 719
- 1.8 GSM Sequences List 719
- 1.9 Operator Names 722
- 1.10 CPHS Information Field 722
- 1.11 CSP Constants 723
- 2 Examples 727
- Command Response 731
- // Wireless CPU 746
- reset is needed 746
- reset is not needed 746
- 3 Technical Appendixes 752
- 3.2 Multiplexing Mode 756
- 000 1001 1 773
- 3.9 USB CDC feature 783
- 4 Interoperability 786
- - New Territories, Hong Kong 787
Produits connexes et manuels pour Récepteur GPS Rainbow-electronics FARGO MAESTRO 100 (with TCP_IP)
(9 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels