Rainbow-electronics AT25F1024 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Stockage Rainbow-electronics AT25F1024. Rainbow Electronics AT25F1024 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 18
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
1
Features
• Serial Peripheral Interface (SPI) Compatible
• Supports SPI Modes 0 (0,0) and 3 (1,1)
• 20 MHz Clock Rate
• Byte Mode and 256-byte Page Mode for Program Operations
• Sector Architecture:
– Two Sectors with 32K Bytes Each (512K)
– Four Sectors with 32K Bytes Each (1M)
– 128 Pages per Sector
• Product Identification Mode
• Low-voltage Operation
– 2.7 (V
CC
= 2.7V to 3.6V)
• Sector Write Protection
• Write Protect (WP) Pin and Write Disable Instructions for
both Hardware and Software Data Protection
• Self-timed Program Cycle (60 µs/Byte Typical)
• Self-timed Sector Erase Cycle (1 second/Sector Typical)
• Single Cycle Reprogramming (Erase and Program) for Status Register
• High Reliability
– Endurance: 10,000 Write Cycles Typical
• Lead-free Devices Available
• 8-lead JEDEC SOIC and 8-lead SAP Packages
Description
The AT25F512/1024 provides 524,288/1,048,576 bits of serial reprogrammable Flash
memory organized as 65,536/131,072 words of 8 bits each. The device is optimized
for use in many industrial and commercial applications where low-power and low-volt-
age operation are essential. The AT25F512/1024 is available in a space-saving 8-lead
JEDEC SOIC and 8-lead SAP packages.
The AT25F512/1024 is enabled through the Chip Select pin (CS
) and accessed via a
3-wire interface consisting of Serial Data Input (SI), Serial Data Output (SO), and
Serial Clock (SCK). All write cycles are completely self-timed.
BLOCK WRITE protection for top 1/4, top 1/2 or the entire memory array (1M) or
entire memory array (512K) is enabled by programming the status register. Separate
write enable and write disable instructions are provided for additional data protection.
Hardware data protection is provided via the WP
pin to protect against inadvertent
write attempts to the status register. The HOLD
pin may be used to suspend any serial
communication without resetting the serial sequence.
Rev. 1440P–SEEPR–6/04
SPI Serial
Memory
512K (65,536 x 8)
1M (131,072 x 8)
AT25F512
AT25F1024
Pin Configurations
Pin Name Function
CS
Chip Select
SCK Serial Data Clock
SI Serial Data Input
SO Serial Data Output
GND Ground
VCC Power Supply
WP
Write Protect
HOLD
Suspends Serial Input
8-lead SOIC
1
2
3
4
8
7
6
5
CS
SO
WP
GND
VCC
HOLD
SCK
SI
8-lead SAP
Bottom View
1
2
3
4
8
7
6
5
VCC
HOLD
SCK
SI
CS
SO
WP
GND
Vue de la page 0
1 2 3 4 5 6 ... 17 18

Résumé du contenu

Page 1 - AT25F1024

1Features• Serial Peripheral Interface (SPI) Compatible• Supports SPI Modes 0 (0,0) and 3 (1,1)• 20 MHz Clock Rate• Byte Mode and 256-byte Page Mode f

Page 2

10AT25F512/10241440P–SEEPR–6/04The READY/BUSY status of the device can be determined by initiating a RDSR instruc-tion. If Bit 0 = 1, the program cycl

Page 3

11AT25F512/10241440P–SEEPR–6/04Timing Diagrams (for SPI Mode 0 (0, 0))Synchronous Data TimingWREN TimingWRDI TimingSOVOHVOLHI-ZHI-ZtVVALID INSIVIHVILt

Page 4

12AT25F512/10241440P–SEEPR–6/04RDSR TimingWRSR TimingREAD TimingCSSCK01234567891011121314SIINSTRUCTIONSO76543210DATA OUTMSBHIGH IMPEDANCE15CSSISCKHIGH

Page 5

13AT25F512/10241440P–SEEPR–6/04PROGRAM TimingHOLD TimingSECTOR ERASE TimingCSSCKSISO3-BYTE ADDRESS1st BYTE DATA-IN256th BYTE DATA-ININSTRUCTIONHIGH IM

Page 6

14AT25F512/10241440P–SEEPR–6/04CHIP ERASE TimingRDID TimingXX = Don’t Care bit12 13 14 15 16 172318 19XMANUFACTURERCODE (ATMEL)DEVICE CODE

Page 7

15AT25F512/10241440P–SEEPR–6/04Ordering InformationOrdering Code Package Operation RangeAT25F512N-10SI-2.7 8S1Industrial(-40°C to 85°C)AT25F1024N-10SI

Page 8

16AT25F512/10241440P–SEEPR–6/04Package Drawing8S1 – JEDEC SOIC1150 E. Cheyenne Mtn. Blvd.Colorado Springs, CO 80906TITLEDRAWING NO.RREV. Note:10/7/0

Page 9

17AT25F512/10241440P–SEEPR–6/048Y4 – SAP1150 E. Cheyenne Mtn. Blvd.Colorado Springs, CO 80817TITLEDRAWING NO.RREV. 8Y4, 8-lead (6.00 x 4.90 mm Body)

Page 10 - AT25F512/1024

Printed on recycled paper.1440P–SEEPR–6/04Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly con

Page 11

2AT25F512/10241440P–SEEPR–6/04Block Diagram Absolute Maximum Ratings*Operating Temperature... −40°C to +85°C*NOT

Page 12

3AT25F512/10241440P–SEEPR–6/04Note: 1. This parameter is characterized and is not 100% tested.Note: 1. VIL and VIH max are reference only and are not

Page 13

4AT25F512/10241440P–SEEPR–6/04Notes: 1. The programming time for n bytes will be equal to n x tBPC.2. This parameter is characterized at 3.0V, 25°C an

Page 14

5AT25F512/10241440P–SEEPR–6/04Serial Interface DescriptionMASTER: The device that generates the serial clock.SLAVE: Because the Serial Clock pin (SCK)

Page 15

6AT25F512/10241440P–SEEPR–6/04SPI Serial InterfaceMASTER:MICROCONTROLLERSLAVE:AT25F512/1024DATA OUT (MOSI)DATA IN (MISO)SERIAL CLOCK (SPI CK)SS0SS1SS2

Page 16

7AT25F512/10241440P–SEEPR–6/04Functional DescriptionThe AT25F512/1024 is designed to interface directly with the synchronous serial periph-eral interf

Page 17

8AT25F512/10241440P–SEEPR–6/04READ PRODUCT ID (RDID): The RDID instruction allows the user to read the manufac-turer and product ID of the device. The

Page 18 - Regional Headquarters

9AT25F512/10241440P–SEEPR–6/04The WRSR instruction also allows the user to enable or disable the Write Protect (WP)pin through the use of the Write Pr

Commentaires sur ces manuels

Pas de commentaire