Rainbow-electronics MAX1209 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Rainbow-electronics MAX1209. Rainbow Electronics MAX1209 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 27
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
General Description
The MAX1209 is a 3.3V, 12-bit, 80Msps analog-to-digital
converter (ADC) featuring a fully differential wideband
track-and-hold (T/H) input amplifier, driving a low-noise
internal quantizer. The analog input stage accepts sin-
gle-ended or differential signals. The MAX1209 is opti-
mized for low power, small size, and high dynamic
performance. Excellent dynamic performance is main-
tained from baseband to input frequencies of 175MHz
and beyond, making the MAX1209 ideal for intermediate-
frequency (IF) sampling applications.
Powered from a single 3.0V to 3.6V supply, the
MAX1209 consumes only 366mW while delivering a
typical signal-to-noise (SNR) performance of 66.5dB at
an input frequency of 175MHz. In addition to low oper-
ating power, the MAX1209 features a 3µW power-down
mode to conserve power during idle periods.
A flexible reference structure allows the MAX1209 to use
the internal 2.048V bandgap reference or accept an
externally applied reference. The reference structure
allows the full-scale analog input range to be adjusted
from ±0.35V to ±1.15V. The MAX1209 provides a com-
mon-mode reference to simplify design and reduce exter-
nal component count in differential analog input circuits.
The MAX1209 supports both a single-ended and differ-
ential input clock drive. Wide variations in the clock
duty cycle are compensated with the ADC’s internal
duty-cycle equalizer (DCE).
ADC conversion results are available through a 12-bit,
parallel, CMOS-compatible output bus. The digital out-
put format is pin selectable to be either two’s comple-
ment or Gray code. A data-valid indicator eliminates
external components that are normally required for reli-
able digital interfacing. A separate digital power input
accepts a wide 1.7V to 3.6V supply, allowing the
MAX1209 to interface with various logic levels.
The MAX1209 is available in a 6mm x 6mm x 0.8mm,
40-pin thin QFN package with exposed paddle (EP),
and is specified for the extended industrial (-40°C to
+85°C) temperature range.
See the Pin-Compatible Versions table for a complete
family of 14-bit and 12-bit high-speed ADCs.
Applications
IF Communication Receivers
Cellular, Point-to-Point Microwave, HFC, WLAN
Ultrasound and Medical Imaging
Portable Instrumentation
Low-Power Data Acquisition
Features
Direct IF Sampling Up to 400MHz
Excellent Dynamic Performance
68.0dB/66.5dB SNR at f
IN
= 70MHz/175MHz
85.1dBc/85.5dBc SFDR at f
IN
= 70MHz/175MHz
3.3V Low-Power Operation
366mW (Single-Ended Clock Mode)
393mW (Differential Clock Mode)
3µW (Power-Down Mode)
Differential or Single-Ended Clock
Fully Differential or Single-Ended Analog Input
Adjustable Full-Scale Analog Input Range: ±0.35V
to ±1.15V
Common-Mode Reference
CMOS-Compatible Outputs in Two’s Complement
or Gray Code
Data-Valid Indicator Simplifies Digital Design
Data Out-of-Range Indicator
Miniature, 40-Pin Thin QFN Package with Exposed
Paddle
Evaluation Kit Available (Order MAX1211EVKIT)
MAX1209
12-Bit, 80Msps, 3.3V IF-Sampling ADC
________________________________________________________________ Maxim Integrated Products 1
Ordering Information
19-1001; Rev 0; 8/04
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
EVALUATION KIT
AVAILABLE
PART
TEMP
RANGE
PIN-PACKAGE
PKG
CODE
MAX1209ETL
-40°C to
+85°C
40 Thin QFN
(6mm x 6mm x 0.8mm)
T4066-3
Pin-Compatible Versions
PART
SAMPLING
RATE (Msps)
RESOLUTION
(BITS)
TARGET
APPLICATION
MAX12553 65 14 IF/Baseband
MAX1209 80 12 IF
MAX1211 65 12 IF
MAX1208 80 12 Baseband
MAX1207 65 12 Baseband
MAX1206 40 12 Baseband
Pin Configuration appears at end of data sheet.
Vue de la page 0
1 2 3 4 5 6 ... 26 27

Résumé du contenu

Page 1 - Pin-Compatible Versions

General DescriptionThe MAX1209 is a 3.3V, 12-bit, 80Msps analog-to-digitalconverter (ADC) featuring a fully differential widebandtrack-and-hold (T/H)

Page 2 - ELECTRICAL CHARACTERISTICS

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC10 ______________________________________________________________________________________626463656667686970

Page 3

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC______________________________________________________________________________________ 1101.51.00.52.52.03.

Page 4

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC12 ______________________________________________________________________________________PIN NAME FUNCTION1

Page 5

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC______________________________________________________________________________________ 13PIN NAME FUNCTION2

Page 6

MAX1209Detailed DescriptionThe MAX1209 uses a 10-stage, fully differential,pipelined architecture (Figure 1) that allows for high-speed conversion whi

Page 7

REFOUT sources up to 1.0mA and sinks up to 0.1mAfor external circuits with a load regulation of 35mV/mA.Short-circuit protection limits IREFOUTto a 2.

Page 8

MAX1209All three modes of reference operation require thesame bypass capacitor combinations. Bypass COMwith a 2.2µF capacitor to GND. Bypass REFP andR

Page 9 - POWER DISSIPATION (mW)

The state of the duty-cycle equalizer input (DCE)changes the waveform at DAV. With the duty-cycleequalizer disabled (DCE = low), the DAV signal is the

Page 10 - MAX1209 toc28

MAX1209for two’s complement (G/T = 0)where CODE10is the decimal equivalent of the digitaloutput code as shown in Table 2.Digital outputs D11–D0 are hi

Page 11 - MAX1209 toc32

Power-Down Input (PD)The MAX1209 has two power modes that are controlledwith the power-down digital input (PD). With PD low, theMAX1209 is in normal o

Page 12 - Pin Description

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC2 _______________________________________________________________________________________ABSOLUTE MAXIMUM R

Page 13 - Pin Description (continued)

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC20 ______________________________________________________________________________________BINARY-TO-GRAY COD

Page 14 - Detailed Description

The circuit of Figure 11 converts a single-ended inputsignal to fully differential just as Figure 10. However,Figure 11 utilizes an additional transfo

Page 15 - Table 1. Reference Modes

MAX1209Buffered External Reference Drives Multiple ADCsThe buffered external reference mode allows for morecontrol over the MAX1209 reference voltage

Page 16 - System Timing Requirements

Unbuffered External Reference Drives Multiple ADCsThe unbuffered external reference mode allows for pre-cise control over the MAX1209 reference and al

Page 17 - INP INN REFP REFN

MAX1209chain providing 2.157V, 1.649V, and 1.141V to theMAX1209’s REFP, COM, and REFN reference inputs,respectively. The feedback around the MAX4230 o

Page 18

etc. SNR is computed by taking the ratio of the RMSsignal to the RMS noise. RMS noise includes all spec-tral components to the Nyquist frequency exclu

Page 19 - Applications Information

MAX1209Aperture JitterFigure 4 depicts the aperture jitter (tAJ), which is thesample-to-sample variation in the aperture delay.Output Noise (nOUT)The

Page 20

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADCMaxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Max

Page 21

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC_______________________________________________________________________________________ 3ELECTRICAL CHARACT

Page 22 - Drives Multiple ADCs

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC4 _______________________________________________________________________________________ELECTRICAL CHARACT

Page 23 - Unbuffered External

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC_______________________________________________________________________________________ 5ELECTRICAL CHARACT

Page 24 - Parameter Definitions

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC6 _______________________________________________________________________________________Note 1: Specificat

Page 25

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC_______________________________________________________________________________________ 7-100-30-40-10-20-7

Page 26 - Pin Configuration

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC8 _______________________________________________________________________________________SNR, SINADvs. SAMP

Page 27 - Package Information

MAX120912-Bit, 80Msps, 3.3V IF-Sampling ADC_______________________________________________________________________________________ 9253530404550556065

Commentaires sur ces manuels

Pas de commentaire